Hello, Welcome to FCTEL Technology Co.,Ltd
National service hotline:+086 0571-87007055/56/57 CN


Products center

16E1-3FE+1*100Base-FX Converter

Type:FCCM-E16F3 Message

Description:16E1/Ethernet interface converter uses reverse multiplexing technology to bundle multiple E1 circuits for transmission of 3*100Base-TX + 1*100Base-FX Ethernet data, enabling 1-16 E1 channels to Ethernet Interface between the conversion, to

Product Description
  16E1/Ethernet interface converter uses reverse multiplexing technology to bundle multiple E1 circuits for transmission of 3*100Base-TX + 1*100Base-FX Ethernet data, enabling 1-16 E1 channels to Ethernet Interface between the conversion, to achieve E1 channel and Ethernet interconnection. The Ethernet encapsulation is in GFP package and supports LCAS and LAPS protocols.
  The device supports flexible configuration of 1 to 16 E1 channels, can automatically detect the number of E1 and select the available E1, and allow a certain transmission delay between the E1 circuit. Single line rate is 1984Kbit / s, 4-way bandwidth of up to 7936Kbit / s, 8-way bandwidth of up to 15872Kbit / s, 16-channel bandwidth of up to 31744Kbit / s.
  With a sound alarm function, the whole work is stable and reliable, low power consumption, high integration, small size. Also has network management module, support stand-alone independent SNMP network management.
Functional Properties
◆  To achieve Ethernet data in 1 to 16 E1 circuit in the transparent transmission;
◆  3 100Base-TX + 1 100Base-FX Ethernet data in 16 E1 transmission;
◆  Ethernet interface 10M / 100M, full / half duplex fully adaptive, support VLAN protocol;
◆  Each Ethernet port supports support for AUTO-MDIX (crossover and straight-line adaptation);
◆  Ethernet interface can also be selected as optical port, to achieve optical data through the E1 remote transmission interconnection;
◆  16-way E1 line, any two between the maximum delay difference of up to 220ms; when the delay difference of more than 220ms, will produce a delay difference overrun alarm, while business interruption;
◆  Built-in dynamic Ethernet MAC address list (4096), with local data frame filtering;
◆  E1 interface conforms to ITU-T G.703, G.704 and G.823, does not support the use of signaling time slots;
◆  Optional local timing and tracking E1 line timing mode, E1 line timing source can automatically switch according to the signal quality. If the system E1 line timing source for the first E1, when the first E1 failure (serious alarm LOS / AIS / LOF / CRC4 or signal loopback) and the second E1 work is normal, the system will automatically switch to tracking The second road E1; failure to eliminate, the system automatically restored to track the first way E1;
◆  Compliant with ITU-T standard protocol, GFP-F package recommendations G.7041, VCAT virtual concatenation and LCAS link capacity adjustment method Recommendation G.7042, Ethernet to nxE1 mapping recommendations G.7043, Ethernet to single E1 mapping Recommendation G.8040 ;
◆  Transmission bandwidth increases, will not damage the Ethernet data; transmission bandwidth man-made reduction, but also through the network management to achieve damage to Ethernet data;
◆  Both ends of the E1 branch can not follow the serial number corresponding to the connection;
◆  When a E1 branch of a single direction failure, the other direction can still work;
◆  E1 signal loopback automatic detection and cut off function: When a ring E1 signal is detected loopback, the system will be cut off the road E1; loop back, this road E1 automatically restored to use;
◆  Complete alarm indication, you can choose to display the local / remote alarm;
◆  Support the remote side / local E1 line side loopback function, to facilitate the E1 line to test;
◆  Support local system on the remote system reset;
◆  Provide command remote interface loopback function, easy line maintenance;
◆  Provide Console management interface, easy to install and open;
◆  Configure the network management module, support independent SNMP network management;
◆  Have the function of displaying the remote device working status at the local end;
◆  A variety of power supply options: AC220V, DC-48V / DC24V, etc .; support AC + DC; AC + AC; DC + DC dual power backup mode;
◆  Can be composed of Ethernet 16E1 bridge (A) --- optical Ethernet 16E1 bridge (B) --- Ethernet fiber optic transceivers (C) topology, can be managed in the A side to the B and C points;
Technical Parameters

◆   Fiber

         Multi-mode Fiber

    50/125um 62.5/125um

    Maximum transmission distance: 5Km @ 62.5 / 125um single mode fiber attenuation (3dbm/km)Wave Length: 820nm

    Transmitting power: -12dBm (Min) ~-9dBm (Max)

    Receiver sensitivity: -28dBm (Min)

    Link budget: 16dBm

        Single-mode Fiber

    8/125um 9/125um

    Maximum transmission distance: 40Km

    Transmission distance: 40Km @ 9 / 125um single mode fiber attenuation (0.35dbm/km)


    Wave Length: 1310nm

    Transmitting power: -9dBm (Min) ~-8dBm (Max)

    Receiver sensitivity: -27dBm (Min)

    Link budget: 18dBm

◆   FXS Phone Interface

    Ring voltage: 75V

    Ring frequency: 25HZ

    Two-line Impedance: 600 Ohm (pick up)

    Return loss: 40 dB

◆   FXO Switch Interface

    Ring detect voltage: 35V

    Ring detection frequency: 17HZ-60HZ

    Two-line Impedance: 600 Ohm (pick up)

    Return loss: 40 dB

◆   EM 2/4 Line

    AD: 0dB

    DA: -3.5dB

    Two/Four-line Impedance: 600 Ohm

    Return loss: 20 dB

◆   Power

    Power supply: AC180V ~ 260V;DC –48V;DC +24V

    Power consumption: ≤10W

◆   Dimension          

    Product Size:    Mini Type    216X140X31mm(WXDXH)

                          19inch       485X200X45mm(WXDXH)

     Piece Weight :    mini 1KG / 19inch  2.4KG

◆   Working environment

    Working temperature: -10°C ~ 50°C
    Working Humidity:        5%~95 % (no condensation)

    Storage temperature:   -40°C ~ 80°C
    Storage Humidity:         5%~95 % (no condensation)

Application Scheme
DataSheet Download